Feed aggregator
CRFS Develops Lightweight RF Sensor for Real-Time Spectrum Monitoring and Geolocation up to 18 GHz
UMS Introduces New GaN Monolithic Front-End IC from 37 to 41 GHz for 5G Applications
Greenerwave Offers Reconfigurable Intelligent Surfaces for 5G FR1, FR2, and FR3 Bands
SOLiD Contributes to Cutting-Edge 5G Open RAN Testing at NTIA-Funded VALOR Lab
Quectel Unveils New Wi-Fi and Bluetooth Module for IoT and Smart Home Applications
Spain Strengthens Airspace Defense with Indra’s Advanced Lanza 3D Radar
Spirent Delivers New 5G Monetization Opportunities with Real-World Testing for FWA
Spirent Communications plc announced its new 5G Fixed Wireless Access (FWA) testing services.
RF Low Noise Amplifiers (LNAs) Applications & Considerations
Throughout the signal chain and especially at a signal input stage, RF signals for communications and sensing can be extremely weak. RF Low Noise Amplifiers (LNAs) are the most common method for increasing the signal level of these very weak signals while minimizing the introduction of signal degrading factors. Of these signal degrading factors, added noise, added phase noise, and distortion are generally of the greatest concerns. However, the limited bandwidth of an LNA may also result in lost signal information.
The dynamic range of an RF system often depends on performance on an LNA near the signal input stage. This input stage can be a signal generator, antenna/probe, or possibly even over a length of lossy transmission line/waveguide path. Another use case for an LNA would be as a bi-directional amplifier. If multiple stages of amplification are needed, the added noise figure and distortion characteristics of the LNA become even more critical.
There is a trade-off in LNA performance with added noise figure, gain, bandwidth, linearity/distortion, size, complexity, cost, ruggedness, and longevity. It is possible to make a very high gain LNA with very low added noise, but this amplifier may have a very limited bandwidth. Conversely, a wide bandwidth LNA may have a good added noise figure but be of limited gain. Design of an LNA requires knowledge of the application and the priorities of the signal chain performance factors. For instance, it may be that the bandwidth requirements necessitate multiple gain stages to ensure wide bandwidth performance while achieving the necessary gain. However, it may be preferable to optimize the noise figure with a single High Gain Low Noise Amplifier stage and sacrifice some bandwidth while keeping a moderate gain level.
Other factors to consider may involve the portability of the LNA. Higher gain, power, and performance LNAs are often generally larger than lower performing LNAs. It may be necessary to use an LNA with poorer performance to retain some power margin. Higher frequency LNAs also tend to be less efficient than lower frequency LNAs, as operating at higher frequencies leads to greater RF losses. Hence, it may be necessary to use multiple LNAs that are optimized over different frequency ranges and multiplexers/filter banks to ensure the desired frequency range is adequately accounted for while meeting system level performance figures.
In terms of linearity, the output power for 1 dB compression/1 dB compression point (P1dB), saturated output power (Psat), and output third order intercept point (IP3) are the most common figures-of-merit (FOMs) considered. Gain flatness and gain variation over temperature or other environmental factors may also be important for some applications that may be exposed to harsh environmental conditions, such as marine, aerospace, extreme climates, or space.
The post RF Low Noise Amplifiers (LNAs) Applications & Considerations appeared first on Pasternack Blog.
HENSOLDT Passive Radar to be Used in Civil Aviation
The sensor solution provider HENSOLDT is working with DFS, the German air navigation service provider, to allow the use of its Twinvis passive radar for civil air traffic safety.
AccelerComm Welcomes Radisys to 5G LEO Satellite Regenerative Base Station Ecosystem Partner Program
Radisys® Corporation announced its inclusion in the AccelerComm® 5G Ecosystem Partner Program, formalizing a long-standing partnership.
EMC Bench Notes: Pre-Compliance Testing for Radiated Emissions, Part 3 – Making the Measurement for MIL and Automotive
Discover pre-compliance testing for automotive and military EMC standards. Learn key differences from commercial testing, setup techniques, and tips for dealing with ambient signals. Save thousands in wasted compliance testing.
The post EMC Bench Notes: Pre-Compliance Testing for Radiated Emissions, Part 3 – Making the Measurement for MIL and Automotive appeared first on In Compliance Magazine.
JFW Industries Introduces New Manual Rotary-Type Attenuator from DC to 3.6 GHz
RFOptic Secures Orders for its 6 GHz RFoF Subsystem from a Fortune 500 Customer
CesiumAstro Unveils New Highly Efficient and Flexible Integrated Phased Array Satellite
Sivers Receives $6 Million CHIPS Act Funding to Advance FR3 Beamformer ICs and Array Design for 5G/6G
Abracon Introduces New Miniature CMOS OCXOs from 10 MHz to 40 MHz for Extreme Environments
Viasat Secures $33.6 Million U.S. Air Force Contract for Advanced Phased Array Antenna Development
RTX to Develop Ultra-Wide Bandgap Semiconductors for DARPA
Raytheon has been awarded a three-year, two-phase contract from DARPA to develop foundational ultra-wide bandgap semiconductors (UWBGS).
Indra Equips the Spanish Air and Space Forces with New State-of-the-Art Radar to Strengthen Air Defence
Indra has completed the implementation and testing of the new Lanza 3D long-range radar to be used by the Air Surveillance Squadron 2 (EVA-2) of the Spanish Air and Space Force.